Working: Mon.-Fri .: 09:00 - 17:00; Sat-Sun: by telephone

Сall back Write to us
Reduced price! Доильный аппарат Березка-1 нержавейка 1500 Expand

Dry Milking machine "Berezka-1 nerzhaveyka"

New

Dry Milking machine "Berezka-1 nerzhaveyka" is intended for milking from 1 to 12 cows per hour, it is equipped with a vacuum pump for 1500 rpm with an increased service life of a dry rotary type on a frame with a receiver; one imported aluminium milk can on 20 l, solid stainless cups, aluminium lid on a can and a standard collector on 140 cm2.

More details

  • Stainless (metal)
  • Rubber (black, replacement 6 months.)
  • Silicone (transparent, replacement 2 years)
  • Standard 140 cm3 (plastic)
  • Increased 240 cm3 (plastic, soft milking)
  • Aluminum (metal)
  • Aluminum 20 L
  • Push pull (synchronous)
  • Pairwise (manual milking imitation) / Bucket lid transparent

12 200,00 грн

12 450,00 грн

-250,00 грн

Dry Milking machine "Berezka-1 nerzhaveyka" is intended for milking from 1 to 12 cows per hour, it is equipped with a vacuum pump for 1500 rpm with an increased service life of a dry rotary type on a frame with a receiver; one imported aluminium milk can on 20 l, solid stainless cups, aluminium lid on a can and a standard collector on 140 cm2.

General characteristics:

  • Type of milking machine: mobile;
  • Recommended continuous working time: 120 minutes, rest 40 minutes;
  • Working temperature of the pump: 80-90°C;
  • Recommended capacity: 10 cows per hour;
  • Simultaneous milking: 1 cow;
  • Milking time per cow: 6-8 minutes;
  • Material of milk tank: aluminium;
  • Milk tank capacity: 20 litres;
  • Material of milking cups: stainless steel;
  • Milk tank lid material: aluminium.


Technical specifications:

  • Vacuum pump: dry rotary vane type;
  • Number of plates: 4 pcs;
  • Plate material: Graphite;
  • Electric power: 0.55 kW;
  • Electricity supply: 220V single-phase;
  • Max. vacuum pressure: 0.08 mPa (80 kPa);
  • Volume of pumped air at idle speed: 220 l/min (7m3/hour);
  • Shaft speed: 1500 rpm.

Dry Milking machine "Berezka-1 nerzhaveyka" is designed to be used in domestic conditions or on small farms. The design of the milking machine on a mobile frame allows it to be easily moved from one cow to another, which makes the whole milking process much easier.

The milking machine requires a constant and stable working vacuum, which is created by a vacuum pump.

The vacuum installation of the milking machine consists of an electric motor and a dry rotary pump, which is installed on the motor shaft without any couplings or pulleys. This construction makes the milking machine small and compact, but at the same time powerful and highly productive. 

The air-cooled dry rotary vacuum pump is designed to generate the vacuum needed for proper milking machine operation and productive milking of cows. It is easy to start and work in cold weather and does not freeze, unlike oil pumps.

Inside the vacuum pump there is a rotating rotor (1), inside which the graphite vanes (2) move freely. As the rotor rotates, the vanes move in the grooves, changing the working volume in the chamber. During suction, the volume increases, creating a vacuum between the blades; when the volume between the blades decreases, the pressure increases and the air escapes through the silencer. 

The milking machine works thanks to a two-stroke milking system (compression and suckling) with a pulse rate of (65±5) pulses per minute and the use of milking cups.

The two-dimensional design of the milking cups consists of two chambers:

  • The external one, which is between the teat rubber and the inside of the milking cup, and connects to the pulsator via the collector distributor;
  • The internal one, which is inside the liners and connects to the collector to collect and discharge milk into the milking bucket.The internal chamber maintains a stable vacuum of between 47 and 52 kPa.

The external chamber is alternately filled with vacuum and air using a pulsator, which causes the linchpin to pulsate. During milking mode, there is a constant vacuum in the outer and inner chambers of the teat, which causes the milk to flow out of the udder. In compression mode, atmospheric pressure enters the outer chamber and the liners are compressed, squeezing the teat. 

Complete with milking machine:

1. 20 litre aluminium milking bucket.

2. PVC milk hose 3 metres long.

3. The lid gasket for the milking bucket.

4. Aluminium milking bucket lid.

5. Polypropylene tee and corner.

6. Vacuum hose 11x23 1m long.

7. Pulsator non-adjustable two-stroke pulsator.

8. Vacuum tube 7x14 3 m long.

9. Plastic manifold 140cc.

10. Rubber nipple - 4 pieces.

11. Polypropylene clamp - 4 pieces.

12. Transparent 7x14 vacuum tube - 1 m.

13. Stainless milking cup - 4 pcs.

14. Rinsing nozzles 1 set (two short and one long).

15. Technical documentation and passport with warranty card.

The vacuum unit is completed:

1. Dry rotary vacuum pump with four graphite plates, 0.55 kW electric motor, 1500 rpm. Supplied with switch-off button and 2 m electric cable with grounding plug.

2. High efficiency silencer.

3. metal frame with space for a dustbin and 3 litre air receiver. 4.

4. Plastic wheel with rubber tyre - 2 pcs,

5. Vacuum regulator.

6. Vacuum gauge.

7. Corner with transparent hose for connecting the pump to the receiver.

Mass dimensions:

- Size: 62x98x108 cm;

- Weight: 42 kg.

Country of manufacturer - Ukraine

Manufacturer - Burenka

 

Производительность1-10 коровы
LinerRubber (black)
Teatcup ShellStainless (metal)
Milking ClawStandard 140 cm3 (plastic)
Bucket LidAluminum (metal)
Milking systemPush pull (synchronous)
Pump Protection Unitwithout BZN (without protection against moisture)
Shaft rotation speed1500 rpm
Number of plates in the pumpGraphite - 4pcs
Pump typeDry rotary
Гарантия24 месяца
Доставка/ОплатаДоставка до 5 дней/Оплата при получении
ПредназначениеДля коров
МатериалКаучук